P0012 OBD Engine Code Logo   Code #P0012 -
'A' Camshaft Position - Timing Over-Retarded (Bank 1)

Select a Code:


Scion tC
Car still runs fine


Mazda Mazda3
rough idle and reduced power


It came up with p0303,p0113,p0456

Scion xB
Lights came on today. The car started up, but the car seems to sputter as we are driving it. There is some reduce power when we turn on the windshield wipers.


Chevrolet Aveo5
P0012COODE


Mercedes-Benz C230
check engine light p0012


P0441 replaced the evap purge valve then started getting p0011 and p0012.

Mercedes-Benz C230
reduced power


p1181

Hyundai Sonata
oil control value


Ford Focus
p00700


Mercedes-Benz C230
engine light on po0117


p0012

Mercedes-Benz ML500
p0012 p0300 p0305 p0304 p0306 p0303 p0307


p0012

car starts hard and sometimes not at all

engine light on

Toyota Corolla
p0012


Toyota Sienna
light on


Hyundai Santa Fe
misses when cold, vibrates or shakes no chk engine light comes on


Jeep Grand Cherokee
i have been searching to find exactly what this code means & have gotten no where. i have talked to several experienced mechanics. my 96 jeep grand Cherokee has 225000 miles. 4.0 inline 6. it has a tap like the valve is hitting. the mechanics think that it jumped timing due to a worn out timing chain. i have not verified this. but it may help others. i do have a loss of power more common in higher RPM. no other codes show in dash.


runs rough and riugh idle

BUSCO INFORMACION AL RESPECTO...

p0012 camshaft timing `A` over retarded bank 1

codigo p0012 hyundai

p0015



Report your Experience!

Tell us about Code #P0012

When did your Check Engine Light Come On?
Does your Car Start?
Does your Car Vibrate? Shake?
Does your Car Idle Roughly? Reduced Power?

Even if you don't know the fix, please provide us all details about your experience to help others!
Make:
Model:
Comments:
 


Other Comments

P0154 engine light came on about 3 miles down road at 65 mph after replacing bank 2 sensor 1

P0882 My 01 pt cruiser sometimes goes into limp mode more often now. It has a 0700 code. I was told to replace the tcm but I am afraid if I do there is actually another problem. When I crank the car if the RPMs are high the car will be in limp mode automatically if no shifts and runs fine, it is all determined when you start the car if it will shift correctly and will be the same until the car is turned off and restarted.

P0660 driving shut off try to start its just clicking

P0513 Key

P0897 After changing the transmission oil and the filters, turn the ignition key to on position, transmission in neutral, shift to drive position, then neutral, back to drive, back to neutral, shift to reverse position and then back to neutral position. this should reset the code.



Other Check Engine Light Codes

P0020   'A' Camshaft Position Actuator Circuit (Bank 2)
P0144   O2 Sensor Circuit High Voltage (Bank 1 Sensor 3)
P0182   Fuel Temperature Sensor A Circuit Low Input
P0292   Cylinder 11 Injector Circuit High
P0453   Evaporative Emission Control System Pressure Sensor High input
P0500   Vehicle Speed Sensor
P0577   Cruise Control input Circuit High
P0864   TCM Communication Circuit Range/Performance
P0942   Hydraulic Pressure Unit
P0992   Transmission Fluid Pressure Sensor/Switch "F" Circuit




Others were Searching For...


Warning: mysql_fetch_assoc() expects parameter 1 to be resource, boolean given in /var/www/OBD/404error.php on line 380





Home - Contact Us
All Content and Images are Copyrights of their respective parties. Copyright SellHI, LLC.